Mixergy offers particulars on its iHP X warmth pump cylinder and explains the right way to set up it. 

The Mixergy iHP X built-in warmth pump cylinder has been designed in order that the warmth pump and cylinder are separate – completely different to different built-in warmth pump cylinders in the marketplace. This design makes it simpler and lighter to move, set up and preserve and it comes pre-plumbed with easy connections designed for straightforward set up.  

Solely G3 unvented certification is required, and no F-GAS qualification is required. Being modular, each the cylinder and the warmth pump unit of the Mixergy iHP X are separate, the whole lot is accessible, and each could be serviced and repaired. 

It’s higher for the top consumer too, as a result of quite than taking hours to warmth a full cylinder of water, it makes use of Mixergy’s distinctive ‘high down’ Stratos know-how. By solely heating the recent water wanted, useable scorching water could be out there in underneath half-hour when in ‘quick increase’ mode. 

It’s designed for patrons who need to save power and be extra sustainable while making certain quick supply of scorching water when it’s wanted. With machine studying, good controls and the Mixergy app, the consumer can set schedules and combine with good tariffs, making it straightforward to make use of, handy for the person wants of every family and cost-effective to run. 

Set up step-by-step
The place of the cylinder ought to swimsuit the set up and all connections must be to the entrance for ease of entry. Guarantee there’s at the least 350mm of vertical clearance above the cylinder from the highest of the ducting spigots. 

Set up of the cylinder must be carried out as per the producer’s directions. The warmth pump unit is then fitted as follows:

Pipework sub-assemblies, three-way ball valve motor, seals and screws are all offered for the job. Ducting for dealing with the exhaust and consumption of air to the warmth pump head unit just isn’t included because the size will fluctuate, relying on the complexity and positioning of the duct. 

Step 1 Lifting the top unit is a two-person job. The top unit have to be lifted by the straps and steadied by holding the fan housing. The top have to be situated by lining up the 4 securing bolts.

Step 2 Match the securing bolts. Necessary: don’t absolutely tighten the bolts till all of the pipework has been fitted and tightened, to permit for adjustment of the top unit relative to the pipework. 

Step 3 The water inlet pipe is fitted between the cylinder and head unit. 

Step 4 The three-way ball valve and related pipework is fitted to the cylinder and the three-way ball valve is fitted to the water outlet connection on the top unit.

Step 5 As soon as all of the connections are made, they are often absolutely tightened.  

Step 6 The three-way ball valve motor is fitted, together with a complete of 4 electrical connections between the controller and head unit. The top unit and immersion feeds are reverse genders to keep away from incorrect meeting and are fitted by pushing the connectors into the sockets and twisting clockwise to lock into place. The sensor and information cables additionally have to be plugged in. 

Step 7 Necessary. The auto air vent have to be opened previous to filling the unit, then as soon as the unit is full and all of the air has been vented, the auto air vent have to be closed. 

Step 8 As soon as the unit has been commissioned, the highest cowl could be fitted and is secured with the 4 self-tapping screws which are equipped. Necessary: the screws have to be fitted to ensure there’s a good seal between the unit and the highest cowl. If the screws should not fitted and the quilt is unfastened, it might impression the house’s heating effectivity. 

The Mixergy iHP X is now prepared for the ducting to be fitted. It makes use of 150mm ducting for the exhaust and consumption of air to the warmth pump head unit. Relying on the complexity of the duct, the utmost size will fluctuate, so please discuss with the set up guide for max mixed duct lengths. 

Please learn the set up guide earlier than putting in the Mixergy iHP X.